All posts by stevecole

Author - Steven Cole (Economics, MBA) - 22 years experience in the reflective safety tape industry.

2 Inch – V52 Reflexite “Diamond Plate” 7/11 and Solid White DOT Tape Rolls

Reflexite V52 – “Diamond Plate Pattern” 7″ White (silver) / 11″ Red & Solid White (silver) DOT Approved Reflective Tape

2″ x 150′ Rolls in 7/11 pattern and solid white both with “diamond plate pattern”

Reflexite V52 10 year rated reflective tape with a “diamond plate pattern”.  Exceeds all State and Federal NHTSA & DOT requirements. On this page we have the 7″ white and 11″ red pattern as well as solid white/silver rolls. The rolls have the DOT-C2 logo imprinted on them. The tape is easy to apply. Just peel off the backing and apply to a clean, dry surface. Then apply pressure using a squeegee or soft cloth. 2″ DOT tapes can be used for DOT applications such as marking tractor trailers. It can also be used to mark boats, motorcycles, guardrails, fences, gates and vehicles.

On this page we carry the “Diamond Plate Pattern V52” Reflexite 7/11 and solid white (see picture below) tape in 2 inch rolls. You can purchase 150 foot rolls by clicking the buttons below. We normally ship out the rolls the day they are ordered. If you need expedited shipping or need any assistance you an call us at 850-934-3157.



2 Inch – V82 Reflexite 6/6, 7/11, Solid White DOT Tape Rolls

Reflexite V82 – 6″ Red / 6″ White (silver), 7″ White (silver)  / 11″ Red & Solid White (silver) DOT Approved Reflective Tape – 50% Brighter than V92

2″ x 150′ Rolls

Reflexite V82 10 year rated reflective tape exceeds all State and Federal NHTSA & DOT requirements. Reflexite’s V82 tape is about 50% brighter than V92 tape. On this page we have the even 6″ red and 6″ white alternating pattern, the 7″ white and 11″ red pattern as well as solid white/silver rolls. The rolls have the DOT-C2 logo imprinted on them. The tape is easy to apply. Just peel off the backing and apply to a clean, dry surface. Then apply pressure using a squeegee or soft cloth. 2″ DOT tapes should be used for DOT applications such as marking tractor trailers.  It can also be used to mark boats, motorcycles, guardrails, fences, gates and vehicles.

On this page we carry the Reflexite 6/6,7/11 and solid white (see picture below) V82 tape in 2 inch rolls. You can purchase 150 foot rolls by clicking the buttons below. We normally ship out the rolls the day they are ordered. If you need expedited shipping or need any assistance you an call us at 850-934-3157.



1″ Rolls Available on this page.

1 Inch – V82 Reflexite 6/6, 7/11, Solid White DOT Tape Rolls

Reflexite V82 – 6″ Red / 6″ White (silver), 7″ White (silver)  / 11″ Red & Solid White (silver) DOT Approved Reflective Tape – 50% Brighter than V92

1″ x 150′ Rolls

1″ V82 10 year DOT Tape can be purchased on this page.

Reflexite V82 10 year rated reflective tape exceeds all State and Federal NHTSA & DOT requirements. Reflexite’s V82 tape is about 50% brighter than V92 tape.  On this page we have the even 6″ red and 6″ white alternating pattern, the 7″ white and 11″ red pattern as well as solid white/silver rolls. The rolls have the DOT-C2 logo imprinted on them. The tape is easy to apply. Just peel off the backing and apply to a clean, dry surface. Then apply pressure using a squeegee or soft cloth. 1″ DOT tapes should be used for Non DOT applications such as marking trailers, boats, motorcycles, guardrails, fences, gates and vehicles. (use 2″ and up for DOT apps)

On this page we carry the Reflexite 6/6,7/11 and solid white (see picture below) V82 tape in 1 inch rolls. You can purchase 150 foot rolls by clicking the buttons below. We normally ship out the rolls the day they are ordered. If you need expedited shipping or need any assistance you an call us at 850-934-3157.



1″ Rolls Available on this page.

School Bus Reflective Tape – Yellow Reflexite V99 or V82 – 1″ – 6″ rolls (Brighter)

Reflexite Yellow V82/V99 Reflective School Bus Tape 1″, 2″ , 3″ , 4″ , 6″ x 150′ Rolls schoolbus4Reflexite Yellow V82 10 year rated reflective school bus tape exceeds all State and Federal NHTSA & DOT requirements.  V82 School Bus tape is approximately 50% brighter than V92 tape.  On this page we have the 1 inch –  6 inch rolls. The tape is easy to apply. Just peel off the backing and apply to a clean, dry surface. Then apply pressure using a squeegee or soft cloth. This tape can also be used on trailers, boats, motorcycles, guardrails, fences, gates, bollards, containers, dumpsters, vehicles and anything else that requires bright night time visibility. You can order 1″ , 2″ ,  3″ , 4″ and 6″ rolls below in 150 foot lengths. We normally ship out the rolls the day they are ordered. If you need expedited shipping or need any assistance you an call us at 850-934-3157. Our main reflective tape and safety products website is www.colebrothers.com.



FMVSS 131 & 217 School Bus Reflective Tape Requirements

Almost all states in the US mandate reflective markings on school buses.  Unlike DOT trucks, regulations concerning school buses fall to the individual states with the federal government providing guidance. Regulations concerning reflective tape are normally found within the regulations of the state that deal with the rest of the bus as well.  (ie exits, seats, seatbelts, fire extinguishers, etc.)

School bus conspicuity treatments generally involve 2-inch prismatic reflective striping in a school bus yellow color down the sides of the vehicle.  Also, 1-inch striping around all exits.  A summary of the federal exit marking regulation is below.

School bus conspicuity treatments generally involve 2-inch prismatic reflective striping in a school bus yellow color down the sides of the vehicle.  Also, 1-inch striping around all exits.  A summary of the federal exit marking regulation is below.

FMVSS 131 & FMVSS 217

School Bus Regulation:

Each opening for a required emergency exit shall be outlined around its outside perimeter with a retroreflective tape with a minimum width of 2.5 centimeters and either red, white, or yellow in color, that when tested under the conditions specified in S6.1 of Standard No. 131 (49 CFR 571.131), meets the criteria specified.

  • 1″ reflective yellow strip used to mark side emergency exit windows
  • 1″ reflective yellow strip used to mark back emergency exit windows
school bus back markings reflective tape
school bus side marking reflective

Private buses fall under DOT C2 regulations because of their size and weight, however, they are not as regulated as school buses. The same type of reflective tape application is highly recommended especially if the bus transports children.

Excerpt from Florida’s School Bus Regulations – There must be installed a reflective marking package as specified in the National School Transportation Specifications and Procedures, Revised 2010. Striping must be installed longitudinally the length of the body at the vertical location immediately below the seat level rub rails but high enough so as to clear wheel wells, whenever possible. Short breaks in the striping at rivet locations are acceptable. Reflective markings are also required for all emergency exits. 

School bus marking regulations

DOT C2 Regulation for Semi Trucks and Large Vehicles

Photo Courtesy of Oralite Americas

Marking DOT-Regulated Trucks and Trailers – Trucks that exceed 10,000 pounds and that are over 80 inches wide must mark their trailers with 2″ wide DOT C2 reflective tape that alternates white and red.. A 6/6 (6″ red and 6″ white) or a 7/11 (7″ white and 11″ red) pattern can be used.  50% of each side must be covered. (even distribution) In the rear, two horizontal red and white strips must be used in the lower rear and an inverted L using solid white must mark the top corners of the trailer. This outlines the back of the rig.

(This is a synopisis of the Federal regulation regarding DOT regulated truck marking. For a word for word copy of the law you can refer to the actual FMCSA document) In summary, to help reduce the incidence of motorists crashing into the rear or sides of tractor-trailers at nighttime and under other conditions of reduced visibility, the FMCSA has set up regulations requiring the use of conspicuity (reflective tape) materials on trailers and the rear of truck tractors. Accidents are reduced by over 40% when these markings are present.

In 1992, the National Highway Traffic Safety Administration or NHTSA published a final ruling requiring that trailers manufactured on or after December 1, 1993, which have an overall width of  80 inches or more and a gross vehicle weight rating (GVWR) of more than 10,000 pounds, (except for pole trailers and trailers designed only for living or office use) be marked on the sides and rear with a means for making them more visible on the road. The NHTSA ruling allows trailer manufacturers to install either red and white retro reflective tape or sheeting or reflex reflectors.  This tape is commonly referred to as “DOT C2 reflective tape” which is marked for easy identification.

Locations for Conspicuity Treatment
The following paragraphs describe where the conspicuity treatments need to be located on trailers. An image is provided at the bottom of this page.

Trailer Sides
2″ wide red and white (silver) DOT C2 retro reflective sheeting must be applied to both sides of the trailer or semitrailer. Each strip of retroreflective sheeting has to be positioned as horizontally as practical, beginning and ending as close to the front and rear as practical. Conspicuity treatment is not required to be continuous, however, the sum of the length of all of the segments must be at least half of the length of the trailer and the spaces between the segments of the strip must be distributed as evenly as possible. The centerline for each strip of retroreflective sheeting (or reflex reflector) must be between 15 inches and 60 inches above the road surface when measured with the trailer empty or unladen, or as close as practical to this area. If necessary to clear rivet heads or other similar obstructions, 50 mm (2 inches) wide retroreflective sheeting may be separated into two 25 mm (1 inch) wide strips of the same length and color, separated by a space of not more than 25 mm (1 inch).

Lower rear area of the Trailer
The rear of each trailer and semitrailer must be equipped with retro reflective sheeting (or reflex reflectors). Each strip of retro-reflective sheeting (or reflex reflector) must be positioned as horizontally as possible, extending across the full width of the trailer, beginning and ending as close to the extreme edges as possible. The centerline for each of the strips of retro-reflective sheeting (or each reflex reflector) must be between 375 mm (15 inches) and 1,525 mm (60 inches) above the road surface when measured with the trailer empty or unladen, or as close as practical to this area.

Upper rear area of the Trailer
Two sets of white strips of retro reflective sheeting (or reflex reflectors), each pair consisting of strips 12 inches long, must be positioned as an inverted L on the right and left upper corners of the rear of the body of each trailer and semitrailer, as close as possible to the top of the trailer and as far apart as practicable. If the perimeter of the body, as viewed from the rear, is not square or rectangular, the conspicuity treatments may be applied along the perimeter, as close as practicable to the uppermost and outermost areas of the rear of the body on the left and right sides.

Reflective DOT C2 Marking Regulation for Trucks. FMVSS 108
Photo Courtesty of Oralite Americas

Rear of Truck
On August 8, 1996, the NHTSA published a final rule requiring that semi trucks manufactured on or after July 1, 1997, be equipped with red-and-white retroreflective material similar to that required on the rear of the trailers they tow to increase nighttime conspicuity. Manufacturers may choose either retroreflective sheeting or reflex reflectors. In the case of truck tractors delivered with a temporary mudflap arrangement rather than permanent equipment, the requirement for retroreflective material near the top of the mudflap may be satisfied with material carried by the temporary mudflap brackets that are transferable to the permanent mudflap system. Retroreflective material is also required near the top of the cab in a pattern similar to that used on trailers.

1 Inch – V92 Reflexite 6/6 DOT Tape Rolls

Reflexite V92 – 6″ Red / 6″ White (silver) DOT Approved Reflective Tape

1″ x 30′ and 1″ x 150′ Rolls

1 Inch – 6″ Red / 6″ White Rolls Sold On This Page

This 5-7 year rated product exceeds all State and Federal NHTSA & DOT requirements. The pattern is an even 6″ red and 6″ white alternating pattern.  The rolls have the DOT-C2 logo imprinted on them.  The tape is easy to apply. Just peel off the backing and apply to a clean, dry surface. Then apply pressure using a squeegee or soft cloth.  1″ DOT tapes should be used for Non DOT applications such as marking trailers, boats, motorcycles, guardrails, fences, gates and vehicles.  (use 2″ and up for DOT apps) 

On this page we carry the Reflexite 6/6 V92 rolls in 1 inch rolls.  You can purchase both 30 foot and 150 foot rolls by clicking the buttons below.  We normally ship out the rolls the day they are ordered.  If you need expedited shipping or need any assistance you an call us at 850-934-3157.




1 Inch – V92 Reflexite 7/11 DOT Tape Rolls

Reflexite V92 – 7″ Red / 11″ White (silver) DOT Approved Reflective Tape

1″ x 30′ and 1″ x 150′ Rolls

This 5-7 year rated conspicuity tape exceeds all State and Federal NHTSA & DOT requirements. The rolls on this page have the 7″ white / 11″ red alternating pattern.  The Reflexite rolls have the DOT-C2 logo imprinted on them. The tape is easy to apply. Just peel off the backing and apply to a clean, dry surface. Then apply pressure using a squeegee or soft cloth.  1″ rolls are to be used for non DOT applications. (2″ and up are for DOT apps)  Examples of applications would be personal trailers, gates, fences, guard rails, non DOT regulated vehicles, bicycles.

On this page we carry the Reflexite 7/11 V92 rolls in 1 inch rolls. You can purchase both 30 foot and 150 foot rolls by clicking the buttons below. We normally ship out the rolls the day they are ordered.  If you need expedited shipping or need any assistance you an call us at 850-934-3157.



1″ & 2″ – V92 Reflexite Solid White DOT Tape Rolls

Reflexite V92 – Solid White (silver) DOT Approved Reflective Tape

  • 1″ & 2″ x 30 foot rolls
  • 1″ & 2″ x 150′ foot rolls

This 5-7 year rated product exceeds all State and Federal NHTSA & DOT requirements. This is a solid white (silver) roll. It has a silvery color in the daylight but reflects a bright white. The tape is easy to apply. Just peel off the backing and apply to a clean, dry surface. Then apply pressure using a squeegee or soft cloth. 1″ DOT can be used for a variety of non DOT applications such as marking vehicles, boats, motorcycles, guardrails, fences, bollards, gates and vehicles.  (For DOT applications on trucks use 2″ or above)

On this page we carry the Reflexite Solid White V92 rolls in 1 inch and 2 inch rolls. You can purchase both 30 foot and 150 foot rolls by clicking the buttons below. We normally ship out the rolls the day they are ordered. If you need expedited shipping or need any assistance you an call us at 850-934-3157.



2 inch – V92 Reflexite 6/6 DOT Tape Rolls

Reflexite V92 – 6″ Red / 6″ White (silver) DOT Approved Reflective Tape

2″ x 30′ and 2″ x 150′ Rolls

2 Inch – 6″ Red / 6″ White Rolls Sold On This Page

This 5-7 year rated product exceeds all State and Federal NHTSA & DOT requirements. The rolls have the DOT-C2 logo imprinted on them.  The tape is easy to apply. Just peel off the backing and apply to a clean, dry surface. Then apply pressure using a squeegee or soft cloth.

On this page we carry the Reflexite 6/6 V92 rolls in  2 inch rolls.  You can purchase both 30 foot and 150 foot rolls by clicking the buttons below.